塑胶喷粉面油墨、塑胶表面喷粉油墨

塑胶喷粉面油墨、塑胶表面喷粉油墨销售厂家！

1本产品主要用于各种金属、玻璃、真空电镀、水电镀、电泳、阳极氧化铝、电解板、铝塑板、喷塑、喷粉、静电喷漆面、烤漆面以及各种天花吊顶氧化板、镜面板、覆膜板、辊涂板、尼龙加玻纤、三聚氰胺板等制品的丝印及移印。
2、产品特性：亮光、附着力佳、快干、耐冲压。耐溶剂，耐白电油，耐正己烷，耐植物油，耐水煮，耐高温
，
，，耐甲苯，耐酸碱，耐汽油，不龟裂、抗皱、抗回粘、回弹性佳、
3、稀释剂：用我司B-03**稀释剂或783开油，用718洗网水清洗网版。
4、固化剂：单组份使用，也可选择添加我司JS-10**固化剂用于增加油墨附着力及物理化学抗性。
5、油墨调配方法：开罐先搅拌均匀，取所需量油墨稀释到合适印刷粘度。如需添加固化剂，先加固化剂搅拌后静置10分钟，待油墨与固化剂完全交联后再进行稀释。
6、干燥时间：常温干燥，表干时间5-10分钟，实干时间在24小时以内，80℃烘烤20分钟可快速干燥。
7、添加固化剂后的使用时限：4-6小时，过期请弃用，剩余油墨不可回收。
颜　  色
透明、蒙砂、黑、白、大红、鲜红、玫红、酒红、桃红、粉玫瑰、粉红、中黄、柠黄、米黄、深蓝、宝蓝、群青、天蓝、姻蓝、深绿、草绿、果绿、紫色、紫罗兰、等多种颜色
【性能检测】
1、3M胶带划百格测试：**无脱落
2、耐冲压测试：1mm厚铝板180°折弯无变化。
3、耐酒精测试：用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
【注意事项】
1、先小量试印确认符合要求后再批量生产。
2、做好承印物的表面清除油脂及杂质工作，以促进附着效果。
3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，
需要完全固化后方可检测。
4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。
5、油墨，稀释剂使用及储存时严禁烟火。
6、使用时注意施工场所的通风状况良好，尽量避免皮肤直接接触。
7、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。
8、技术参考数见下表：
   检验项目 检验结果 测试条件 
   油墨线度 ≤12um 刮板细度计 
   干膜光泽 ≥65° 60°镜面光泽计 
   干燥速度 表干 25℃×5-10min 或60℃×2-3min 
   实干 25℃12Hr或60℃×10min 
   耐酒精性 无变化 500克力/cm2酒精棉200次来回 
   附着力 100/100 1mm×1mm×100格3M胶纸剥离 
   耐酸性 无变化 浸泡5%HCI×24Hr 
   耐碱性 无变化 浸泡5%NaOH×24Hr 
   耐盐性 无变化 浸泡5%NaCI×24Hr  
   耐水性 无变化 浸泡20℃自来水×96Hr   
   耐磨性 不见底 500克/cm2负载含砂橡皮200来回 
   耐热性 无变化 80℃×12Hr 
1 this product is mainly used for screen printing and printing all kinds of metal, glass, vacuum plating, electroplating, electrophoresis, anodic alumina water, electrolytic plate, aluminum plate, plastic spraying, powder spraying, electrostatic spraying, baking paint surface and various ceiling panels, mirror panels, oxide coated board, roller coated plate, nylon with glass fiber, melamine board other products.
2, product characteristics: gloss, adhesion, impact resistance, quick drying.  Solvent resistance, resistance to white oil, n-hexane, plant oil, water resistance, high temperature resistance
,
Toluene resistant, acid and alkali resistant, gasoline resistant, no cracking, anti crease, anti sticky, good resilience,
3, diluent: use our B-03 special diluent or 783 to open the oil, and use 718 net water to clean the net plate.
4, curing agent: one, can also choose to add our JS-10 special curing agent used to increase the ink adhesion and chemical resistance.
5, the method of printing ink: mixing the tank first and taking the required ink to the appropriate printing viscosity. If the curing agent is added, the solidifying agent is stirred for 10 minutes after mixing, and then the ink is completely crosslinked with the curing agent and then diluted.
6, drying time: drying at normal temperature, 5-10 minutes of dry time, 24 hours of actual drying and 20 minute drying for 20 minutes at 80 C.
7, the use time limit after adding curing agent: 4-6 hours, expired please discarded, the remaining ink can not be recycled.
Color
Transparent, frosted, black, white, red, red, red, red wine, pink, pink roses, pink, yellow, lemon yellow, beige, blue, blue, dark blue, sky blue, blue, green, dark green, because green, purple, violet and other colors
[performance detection]
1, 3M tape test: ** no shedding
2, resistance to stamping test: 1mm thick aluminum plate 180 degree bending no change.
3. Alcohol tolerance test: 99% industrial alcohol was stained with skimmed cotton at 500G force level for 200 times without decolorization.
[cautions]
1, the first small test print confirms that it meets the requirements and then batch production.
2, do a good job of removing oil and impurities on the surface of the material to promote the effect of attachment.
3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, wear resistance, etc.
Need to be completely cured in the rear and can be detected.
4. In the absence of permission, this series of ink can not be mixed with other types of ink and color matching.
5. Ink, the use and storage of diluents strictly prohibit fireworks.
6, in use, pay attention to the ventilation of the construction site is good, try to avoid direct contact of the skin.
7, this product is inadvertently splashed in the entrance, nose, eye and ear, and uses a lot of water to clean or direct to the doctor.
8. The number of technical references is shown in the following table:
Test conditions for test results of inspection items
The ink line is less than 12um fineness dispersion meter
Dry film gloss is not less than 65 DEG C 60 DEG specular gloss meter
Dry speed meter dry 25 x 5-10min or 60 C 2-3min
Dry 25 C 12Hr or 60 C * 10min
No change in alcohol tolerance of 500 grams of /cm2 alcohol cotton 200 times back and forth
Adhesion of adhesive force 100/100 1mm x 1mm x 100 lattice 3M adhesive paper
Soaking 5%HCI * 24Hr without change in acid resistance
Soaking 5%NaOH * 24Hr without change in alkali resistance
Salt tolerance and no change in 5%NaCI x 24Hr
Water resistance, no change, soaking at 20 centigrade tap water x 96Hr
Wear resistance not bottom 500 g /cm2 load containing sand and rubber 200 back and forth
No change of heat resistance at 80 degrees C * 12Hr